Ceramic/
Natural Stone

Textile/Resilient

Wood Floors

Safety Precautions

Novelties

MSDS

printable version

pdf version

Premium Patching and Skim Coating Compound ServoFine F 333

needs no priming or additives

for wide array of substrates like ceramic tiles, wood, quarry tile, adhesive residues

provides a true featheredge

excellent skim coating properties

extremly smooth surface

fast setting, fast drying

Properties and usage

Cement-based patching and skim coating compound with very fine grain and high polymer content.
For application without primer or liquid additives on different kinds of substrates: old tiles, terrazzo, wood, screed, raw concrete floors, well prepared adhesive residues and alike. Provides a very fine grain for a true featheredge for easy skim coating an patching of indents, holes, cracks and uneven areas. Ideal for height transitions and to repair thresholds and pedestals.
ServoFine F 333 can be installed from a true featheredge up to 1" (25 mm)thickness over large areas in one application.
ServoFine F 333 is formulated to dry the mixing water within itself and therefor provides a short drying time.
Do not use ServoFine F 333 as final load top.

Specifications

Color

gray

Application

interior

Thickness

featheredge to 1" (25 mm) thickness with tension free curing

Suitable for chair castors
(according DIN EN 12 529)

min. 2 mm (1/16")

Coverage

approx. 20 sq. ft. per bag for 1/8" thickness
approx. 1.1 kg/m² per mm thickness

Application temperature*

41°F to 77°F (+5°C to +25°C ) (substrate)

Ratio of water

approx. 0.35 - 0.40 US gal./10.5 lbs powder
(approx. 1.3 - 1.5 l/4.75 kg powder )

Processing time*

approx. 15 minutes

Ready for traffic*

after approx. 30 minutes

Ready for installation*

after approx. 1 - 1.5 hours

Floor heating systems

suitable

GISCODE

ZP 1 - low in chrome according to TRGS 613

Shelf life

store in a dry place for up to 12 months

* At 68 °F (+20 °C ) and 65% relative humidity. Higher temperature and low humidity decreases, lower temperature and high humidity increases this value respectively.

Substrate preparation

The substrate must be structurally sound and clean. Remove dirt, paint, oil, grease, wax, loose particels and patches and other contaminations which might act as a bondbreaker.
Existing adhesive residues must be tested that they are not water-soluble and do not react with the new flooring adhesive. The new covering material shall not allow the bleedthrough of cutback adhesive residues.

Processing

Use clean water to mix ServoFine F 333 smoothly with an electric mixer at approx. 600 RPM. Apply with leveling trowel. Apply sufficient pressure for smooth application of the compound and to fill all defects and indents. Without the need of priming or liquid additives ServoFine F 333 has no minimum thickness. Even the thinnest layer will cure. Cut edges after approx. 20 - 30 minutes or smoothen with moist leveling trowel if necessary.
Avoid direct sun exposure and draught during the curing process.
A test in a small area prior to application is recommended.

Cleaning

Clean tools with water immediately after application

Note

The information is based on our experience and is to be regarded as general instructions. We cannot guarantee successful results since we do not have any influence on the conditions at the construction site and the proper processing. In any case a sample application is recommended before the installation.

Packaging

Packaging Product Code
50 units je 4 x 4.75 kg (10.5 lbs) bags 42030
72 x 12.5 kg 27.6 lbs)paper bags 42034

Revised

21.08.08

back

printable version

pdf version