Ceramic/
Natural Stone

Textile/Resilient

Wood Floors

Safety Precautions

Novelties

MSDS

printable version

pdf version

White Flexible Thin Set Mortar ServoStar® 3000 Flex weiß

white color for translucent coverings

excellent sag resistance and bond strength

very good coverage

long pot life and open time

also for critical substrates and dense covering materials

tested by external test laboratory

Properties and usage

Sag resistant, flexible, cement-based thin set mortar of white color according to EN 12 004 C2 TE-S1 for interior and exterior ceramic and quarry tile installations, porcelain stoneware, porcelain and glass mosaic, clinker and brick tile and non-watersensitive natural stone over load bearing substrates such as in situ concrete (at least 6 months old) and gypsum fiber board, sheet rock, heated screed (please follow corresponding regulations and data sheets), poured mastic asphalt, autoclaved aerated concrete (AAC) as well as balconies and patios.
By adding 10 % Okamul DZ 18 also suitable for glas mosaic in underwater installations.

Specifications

Color

white

Application

interior, exterior **, walls and floors

Thickness

max. 3/16" (5 mm) (as leveling layer)

Application temperature*

41 °F to 77 °F (+5 °C to +25 °C ) (substrate)

Temperature tolerance

-4 °F to 176 °F (-20 °C to +80 °C )

Water ratio

approx. 8.0 l/25 kg approx. 2.1 US gal./55 lbs. powder

Slake time

approx. 5 minutes (restir)

Processing time*

approx. 3 hours

Open time*

approx. 30 minutes

Ready for light traffic/grouting*

after approx. 24 hours

Marked according to GefStoffV regulations

irritant (contains portland cement)

GISCODE

ZP 1 - low in chrome according to TRGS 613

Shelf life

store in unopened packaging in a dry area for up to 12 months

At 68° F (+20 °C ) and 65% relative humidity. Higher temperature and low humidity decreases, lower temperature and high humidity increases this value respectively.

Avoid air entrapment doing exterior installations. Apply mortar on substrate and the backside of tiles (buttering-floating procedure).

***

When blended with Okamul DZ 18

Substrate preparation

The substrate must be ready for installation, dry, clean and load bearing. If installation occurs on shrinking substrates frequent expansion joints should be included in the layout.
Prime absorbent substrates in interior areas with Okamul GG or Okatmos® UG 30. Allow a drying time of at least 24 hours over calcium sulfate screed. Prime non-absorbent substrates with Okatmos® UG 30.
In exterior areas apply a contact layer of adhesive mortar and let it set.

Processing

Mix ServoStar® 3000 Flex weiß with clean water to a smooth texture. Allow mixture to slake for approx. 5 minutes and stir again. Use appropriate notched trowel (see table) to apply mortar onto substrate, slide the covering material into the adhesive bed within 25 minutes and press tightly. Depending on the absorbency of the substrate/covering corrections can be made within 25 minutes.

Cleaning

Clean tools and tile surface immediately with water.

Note

The information is based on our experience and is to be regarded as general instructions. We cannot guarantee successful results since we do not have any influence on the conditions at the construction site and the proper processing. In any case a sample application is recommended before the installation.

Tools and coverage

maximum tile
dimensions square notched
trowel size coverage
(powder)

up to 2"
(< 50 mm) 1/8" x 1/8" x 1/8"
(3 mm) approx. 1.1 kg/m²
(244 sq. ft. per bag)

2 - 4"
(51 - 108 mm) 4 mm
(or equivalent) approx. 1.4 kg/m²
(192 sq. ft. per bag)

4 - 8"
(109 - 200 mm) 1/4" x 1/4" x 1/4"
(6 mm) approx. 2.1 kg/m²
(128 sq. ft. per bag)

over 8"
(> 200 mm") min. 8 mm
(or equivalent)< approx. 2.7 kg/m²
(99 sq. ft. per bag)
Quantities are approximate and are given for estimating purposes only. They may vary according to substrate conditions and other factors.

Packaging

Packaging Product Code
42 x 55 lbs (25 kg)paper bags 13094

Revised

20.05.08

back

printable version

pdf version